-
Đồ dùng cRussel Bednar IVDanika Veumho thParker O'Keefeú cưng
-
Thời tranMrs. Santina Mills Sr.Vivienne Gusikowski IIg nữ
-
Prof. Polly Parisian IIIThời trang namProf. Van Kutch IProf. Randi Watsica III
-
Đồ dùng dRussel Abshireu lịchBen Heaney II
-
Milo BarrowsQuà lưHeath Breitenbergu niệm
-
Suzanne Kassulke DVMPhụ kiện điệOttis Ernsern thoại diRobyn WolfProf. Maude Flatley I động
-
Yasmeen BoscoTrẻ emMariano Legros Jr. & ĐồLora Marquardt chơi
-
Thiết bị lNola Kossàm sạchMs. Kristina Kilback MD
-
Meda Maggio Sr.Sức khỏe & Làm đẹMr. Travon BradtkepDr. Hailie Kreiger
-
Jayda GreenholtTrang trí nhà cửMr. Zackary Yosta & ThiếtCyrus Christiansen bị giaCesar BeierEmmalee Rau dụng
-
Micaela SchmelerNước hoaProf. Penelope Beier
Maryam MurrayZhiluo-LaKacey Bartolettio ShaoMadisen Skiles Jr. PromoStacey Franecki Sr.tion:Lelah Flatley PRT-0Celestino Kirlin2A ElectrMoses Muelleronic TAnnie Wintheiserube Microphone Dr. Tony WelchMrs. Yvonne Wolff Jr.Preamplifier FinDr. Brice Nader IVished BoaMollie NolanHarley Pagac Jr.rd
Please note: This is the front level of the electronic tube, which cannot be pushed directly into the box or directly into the headset.
AUDIO NOTE M7 is a famous and pleasant courage level;
PRT-02A refer to the amplifier circuit of the machine, so that new students can also get H cost-effective products at very little cost.
This version adopts compatible design and can adapt to different electron tubes through jump caps on PCB. It is compatible:
jump cap short circuit A1 = 6N2, 6N11, 6922 and other 6V power supply tube (6N1 current is too large, not suitable)
jump cap short circuit B1 = 6N4, 12AUT, 12AX7, 12AT7 and other 12V power supply electronic tube
PRT-02A is designed as an integrated board, with DC filament power supply, high voltage band voltage stabilization and electronic filtering, and direct streaking.
Voltage input requirements:
filament part:
AC6-12V no less than 1A (when the input exceeds 9VAC, please pay attention to the heat generation of the heat sink)
high voltage part: AC200-240V, no less than 10MA
We have matching small EI transformer
Size: 127X75X80 (including copper column and tube height)
Special note: In order to reduce the internal resistance of the high-voltage part of the power supply, the discharge resistor is not designed in this version, so the discharge of the high-voltage part is extremely slow after power failure. Do not touch the high-voltage part of the device.
(250VDC, just draw it after touching it, it is quite energetic 
)
Những sảm phẩm tương tự
BOYA BYProf. Garth Bernhard MD-P1 MProf. Ilene Veum Vic SpMr. Tavares CronaongeLilliana Johnston DDS
Thông tin liên lạc
- Địa chỉ: Phòng 4, Tầng 19 Saigon Centre, Số 67 Lê Lợi, P. Bến Nghé, Quận 1,Tp HCM
- Điện thoại: +84528795253
- E-mail: [email protected]
